Astronomik MaxFR-Filters
Astronomik Narrowband-Emissionline filters optimized for fast optical systems!
The MaxFR coating ensures that the Astronomik Narrowband-Emissionline filters can be used with extremely fast optical systems such as the Celestron RASA and the Takahashi Epsilon Astrographs. Unlike other manufacturers' filters, which often require special “High-Speed” versions, Astronomik’s MaxFR filters maintain their transmission characteristics even with normal optical systems.
Filters with MaxFR coating can be used without restriction on the following instruments:
- 12nm filters with MaxFR coating: Instruments with aperture ratios from f/1.7 to f/6 and approximately 15% reduced transmission at f/1.4
- 6nm filters with MaxFR coating: Instruments with aperture ratios from f/2.2 to f/6 and approximately 10% reduced transmission at f/2
- 4nm filters with MaxFR coating are currently in development.
- Filters for even faster optics are available on request.
Furthermore, the Astronomik MaxFR coating offers extremely high contrast, minimized stray light, no halos and needle-sharp stars as well as the best possible blocking across the entire spectral range from UV to IR.
Astronomik OIII 12nm MaxFR Clip-Filter EOS APS-C
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 6nm MaxFR Clip-Filter EOS R XL
The Astronomik H-alpha filter is ideal for imaging HII regions from both light-polluted and dark observation sites. The Astronomik H-alpha filter significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background, allowing for long exposure times for deep and high-contrast images. The filter blocks the emission lines of high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, the maxima of typical LED lights, most lines of natural airglow, as well as most of the distracting moonlight. The Astronomik H-alpha filter effectively blocks all unwanted light from wavelengths other than 656nm, from ultraviolet (UV) to infrared (IR). The Astronomik H-alpha filter MUST NOT BE USED for solar observation! Difference between Astronomik 12nm, 6nm and 4nm filters The choice between 12nm, 6nm and 4nm Full-Width-Half-Maximum (FWHM) filters depends on your imaging conditions and camera type. There is no universal “best” option - each FWHM serves a specific purpose. The 6nm Astronomik Narrowband-Emissionline filters are usually the best choice for astrophotography. They are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image compared to 12nm filters, greatly simplifying image processing. The 6nm Narrowband-Emissionline filters are the first choice, especially if you are using a CMOS astro camera or a modern system camera with very low dark current, or if you are observing from a location with strong light pollution. The excellent suppression of the sky background allows you to use long exposure times. The 6nm filters provide a dark background and outstanding details of faint nebulae. The Astronomik MaxFR coating Both the Astronomik MFR and MaxFR coatings offer extremely high contrast, minimized stray light, no halos and needle-sharp stars. In addition, they provide the best possible blocking across the entire spectral range from UV to IR. The MaxFR coating ensures that the Astronomik Narrowband-Emissionline filters can be used with extremely fast optical systems such as the Celestron RASA and the Takahashi Epsilon Astrographs. Unlike other manufacturers' filters, which often require special “High-Speed” versions, Astronomik’s MaxFR filters maintain their transmission characteristics even with normal optical systems of slower focal ratios. Using a MaxFR filter with a normal optical system has no drawbacks and saves you a lot of money on multiple filter sets. For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2. Clip-Filters for mirrorless Canon EOS R cameras Canon EOS R series cameras are an excellent choice for astrophotography. With Astronomik Clip-Filters, you can use our full range of filters with your camera to capture stunning images. Whether paired with a camera lens or a telescope, our Clip-Filters ensure maximum image quality and performance from your setup. The Astronomik Clip-Filters offer a number of practical advantages that make them an ideal choice for astrophotographers: Installing and removing the Astronomik Clip-Filter is very quick and easy and requires no extra tools or modifications to the camera body. They can be changed at any time, even at night. All lens functions, such as focus, aperture, and image stabilization remain fully functional. The Astronomik Clip-Filters are held securely in place without stressing the high-quality glass. The Astronomik Clip-Filters are designed and optimized for use with both standard camera lenses and telescopes. Through the Astronomik Clip-Filters, we were able to solve several common issues faced by astrophotographers: Large filters for large camera lenses are very expensive. Using a filter holder between the camera body and the lens prevents focusing to infinity. For very fast telescopes (low f-number) like the Vixen R200SS or the Takahashi “Epsilon” astrograph, a filter drawer or filter wheel can not be used because the distance to the corrector lenses would be changed. Long exposure times lead to dust settling on the camera’s sensor chip. Additionally, all Astronomik EOS R XL Clip-Filters serve as an excellent dust shield, protecting the sensor during long exposures. If you only need a dust shield without filtering effects, the Astronomik MC-Clear EOS R XL Clip-Filter is the right choice. Use Astronomik filters for your Canon EOS R camera and enjoy marvelous images with an ultra-light equipment! NOTE: Please store the Clip-Filter in the supplied storage box and do not leave it in the camera permanently. Compatible Canon EOS R full-frame cameras Model Compatibility Canon EOS R Canon EOS Ra * Canon EOS RP Canon EOS R3 Canon EOS R5 Canon EOS R5 Mark II Canon EOS R6 Canon EOS R6 Mark II Canon EOS R8 * Please note: Canon’s astro-version “Ra” of the R-series shows strong halos around brighter stars, even without any filter. We highly recommend NOT purchasing the Canon EOS Ra. Compatible Canon EOS R APS-C cameras Model Compatibility Canon EOS R7 Canon EOS R10 Canon EOS R50 Canon EOS R50 V Canon EOS R100 Non-compatible Canon lenses Model Compatibility Canon RF 14mm f/1.4 L VCM Canon RF 28mm F2.8 STM Canon RF 35mm F1.8 IS Macro STM Canon RF 85mm F1.2L USM Canon Extender RF 2x Canon Extender RF 1.4x Technical Data Guaranteed transmission of more than 90% at the H-alpha line (656nm) Typical transmission of 93% at the H-alpha line Full-Width-Half Maximum (FWHM): 6nm Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters) Finely polished optical glass, free of any striae, residual stresses, and bubbles Extremely scratch-resistant and durable coating Completely resistant against high humidity and aging effects Astronomik MaxFR coating (Astronomik 6nm and 12nm Narrowband-Emissionline filters) Parfocal with other Astronomik filters Diffraction-limited Optimized spectral windows Delivered in a high-quality, long-lasting filter box Made in Germany Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Thanks to the high-precision machining of the glas substrate, all Astronomik filters are parfocal. The wedge errors are far below all common tolerances. Therefore, all issues concerning focal distances and the exact alignment of images from each color channel are effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR and MaxFR coatings are designed for optimal performance across a wide range of focal ratios of the optics used. Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios for best performance of that specific filter.
Astronomik OIII 12nm MaxFR Clip-Filter EOS R APS-C
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 12nm MaxFR Clip-Filter Nikon Z XL
The Astronomik H-alpha filter is ideal for imaging HII regions from both light-polluted and dark observation sites. The Astronomik H-alpha filter significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background, allowing for long exposure times for deep and high-contrast images. The filter blocks the emission lines of high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, the maxima of typical LED lights, most lines of natural airglow, as well as most of the distracting moonlight. The Astronomik H-alpha filter effectively blocks all unwanted light from wavelengths other than 656nm, from ultraviolet (UV) to infrared (IR). The Astronomik H-alpha filter MUST NOT BE USED for solar observation! Difference between Astronomik 12nm, 6nm and 4nm filters The choice between 12nm, 6nm and 4nm Full-Width-Half-Maximum (FWHM) filters depends on your imaging conditions and camera type. There is no universal “best” option - each FWHM serves a specific purpose. The 12nm Astronomik Narrowband-Emissionline filters are optimized for use with system cameras with CMOS sensors. They are also a good choice for CCD cameras with normal or high dark current. The 12nm filters are also the preferred choice for cameras with an integrated or dual guiding sensor, as they show more guiding stars compared to filters with 6nm or 4nm FWHM. The 12nm filters are the most affordable way to get started with Narrowband-Emissionline filters. Usually, the background signal in images taken from suburban or dark-sky locations is limited by the sensor’s dark current rather than light pollution. Therefore, further suppression of the sky background by reducing the FWHM does not reveal more details of the object. The Astronomik MaxFR coating Both the Astronomik MFR and MaxFR coatings offer extremely high contrast, minimized stray light, no halos and needle-sharp stars. In addition, they provide the best possible blocking across the entire spectral range from UV to IR. The MaxFR coating ensures that the Astronomik Narrowband-Emissionline filters can be used with extremely fast optical systems such as the Celestron RASA and the Takahashi Epsilon Astrographs. Unlike other manufacturers' filters, which often require special “High-Speed” versions, Astronomik’s MaxFR filters maintain their transmission characteristics even with normal optical systems of slower focal ratios. Using a MaxFR filter with a normal optical system has no drawbacks and saves you a lot of money on multiple filter sets. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4. Clip-Filter for mirrorless Nikon Z full-frame cameras Mirrorless full-frame Z-series cameras from Nikon are an excellent choice for astrophotography. With Astronomik Clip-Filters, you can use our full range of filters with your camera to capture stunning images. Whether paired with a camera lens or a telescope, our Clip-Filters ensure maximum image quality and performance from your setup. The Astronomik Clip-Filters offer a number of practical advantages that make them an ideal choice for astrophotographers: Installing and removing the Astronomik Clip-Filter is very quick and easy and requires no extra tools or modifications to the camera body. They can be changed at any time, even at night. All lens functions, such as focus, aperture, and image stabilization remain fully functional. The Astronomik Clip-Filters are held securely in place without stressing the high-quality glass. The Astronomik Clip-Filters are designed and optimized for use with both standard camera lenses and telescopes. Through the Astronomik Clip-Filters, we were able to solve several common issues faced by astrophotographers: Large filters for large camera lenses are very expensive. Using a filter holder between the camera body and the lens prevents focusing to infinity. For very fast telescopes (low f-number) like the Vixen R200SS or the Takahashi “Epsilon” astrograph, a filter drawer or filter wheel can not be used because the distance to the corrector lenses would be changed. Long exposure times lead to dust settling on the camera’s sensor chip. Additionally, all Astronomik Nikon Z XL Clip-Filters serve as an excellent dust shield, protecting the sensor during long exposures. If you only need a dust shield without filtering effects, the Astronomik MC-Clear Nikon Z XL Clip-Filter is the right choice. Use Astronomik filters for your Nikon Z full-frame camera and enjoy marvelous images with an ultra light equipment! Compatible Nikon Z full-frame cameras Model Compatibility Nikon Z 5 Nikon Z6 Nikon Z 6II Nikon Z6III Nikon Z7 Nikon Z 7II Nikon Z 8 Nikon Z 9 Nikon Z f Nikon APS-C cameras Non-compatible lenses Model Compatibility Original Nikon Z teleconverter TC-2.0x Technical Data Guaranteed transmission of more than 90% at the H-alpha line (656nm) Typical transmission of 96% at the H-alpha line Full-Width-Half Maximum (FWHM): 12nm Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters) Finely polished optical glass, free of any striae, residual stresses, and bubbles Extremely scratch-resistant and durable coating Completely resistant against high humidity and aging effects Astronomik MaxFR coating (Astronomik 6nm and 12nm Narrowband-Emissionline filters) Parfocal with other Astronomik filters Diffraction-limited Optimized spectral windows Delivered in a high-quality, long-lasting filter box Made in Germany Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Thanks to the high-precision machining of the glas substrate, all Astronomik filters are parfocal. The wedge errors are far below all common tolerances. Therefore, all issues concerning focal distances and the exact alignment of images from each color channel are effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR and MaxFR coatings are designed for optimal performance across a wide range of focal ratios of the optics used. Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios for best performance of that specific filter.
Astronomik OIII 6nm MaxFR Clip-Filter EOS R APS-C
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 6nm MaxFR 36mm
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 6nm MaxFR Clip-Filter EOS APS-C
The Astronomik H-alpha filter is ideal for imaging HII regions from both light-polluted and dark observation sites. The Astronomik H-alpha filter significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background, allowing for long exposure times for deep and high-contrast images. The filter blocks the emission lines of high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, the maxima of typical LED lights, most lines of natural airglow, as well as most of the distracting moonlight. The Astronomik H-alpha filter effectively blocks all unwanted light from wavelengths other than 656nm, from ultraviolet (UV) to infrared (IR). The Astronomik H-alpha filter MUST NOT BE USED for solar observation! Difference between Astronomik 12nm, 6nm and 4nm filters The choice between 12nm, 6nm and 4nm Full-Width-Half-Maximum (FWHM) filters depends on your imaging conditions and camera type. There is no universal “best” option - each FWHM serves a specific purpose. The 6nm Astronomik Narrowband-Emissionline filters are usually the best choice for astrophotography. They are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image compared to 12nm filters, greatly simplifying image processing. The 6nm Narrowband-Emissionline filters are the first choice, especially if you are using a CMOS astro camera or a modern system camera with very low dark current, or if you are observing from a location with strong light pollution. The excellent suppression of the sky background allows you to use long exposure times. The 6nm filters provide a dark background and outstanding details of faint nebulae. The Astronomik MaxFR coating Both the Astronomik MFR and MaxFR coatings offer extremely high contrast, minimized stray light, no halos and needle-sharp stars. In addition, they provide the best possible blocking across the entire spectral range from UV to IR. The MaxFR coating ensures that the Astronomik Narrowband-Emissionline filters can be used with extremely fast optical systems such as the Celestron RASA and the Takahashi Epsilon Astrographs. Unlike other manufacturers' filters, which often require special “High-Speed” versions, Astronomik’s MaxFR filters maintain their transmission characteristics even with normal optical systems of slower focal ratios. Using a MaxFR filter with a normal optical system has no drawbacks and saves you a lot of money on multiple filter sets. For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2. Clip-Filter for Canon EOS APS-C DSLR cameras Canon EOS DSLR cameras with APS-C sensors are an excellent choice for astrophotography. With Astronomik Clip-Filters, you can use our full range of filters with your camera to capture stunning images. Whether paired with a camera lens or a telescope, our Clip-Filters ensure maximum image quality and performance from your setup. The Astronomik Clip-Filters offer a number of practical advantages that make them an ideal choice for astrophotographers: Installing and removing the Astronomik Clip-Filter is very quick and easy and requires no extra tools or modifications to the camera body. They can be changed at any time, even at night. All lens functions, such as focus, aperture, and image stabilization remain fully functional. The Astronomik Clip-Filters are held securely in place without stressing the high-quality glass. The Astronomik Clip-Filters are designed and optimized for use with both standard camera lenses and telescopes. Through the Astronomik Clip-Filters, we were able to solve several common issues faced by astrophotographers: Large filters for large camera lenses are very expensive. Using a filter holder between the camera body and the lens prevents focusing to infinity. For very fast telescopes (low f-number) like the Vixen R200SS or the Takahashi “Epsilon” astrograph, a filter drawer or filter wheel can not be used because the distance to the corrector lenses would be changed. Long exposure times lead to dust settling on the camera’s sensor chip. The Astronomik EOS APS-C Clip-Filters are made from black anodized aluminum. Additionally, all Astronomik EOS APS-C Clip-Filters serve as an excellent dust shield, protecting the sensor during long exposures. If you only need a dust shield without filtering effects, the Astronomik MC-Clear EOS APS-C Clip-Filter is the right choice. Use Astronomik filters for your Canon EOS APS-C DSLR camera and enjoy marvelous images with an ultra light equipment! Compatible Canon EOS APS-C DSLR cameras Model Compatibility Canon EOS-1D (all variants) Canon EOS 5D (all variants) Canon EOS 7D Canon EOS 7D Mark II Canon EOS 20D Canon EOS 20Da Canon EOS 30D Canon EOS 40D Canon EOS 50D Canon EOS 60D Canon EOS 60Da Canon EOS 70D Canon EOS 77D Canon EOS 80D Canon EOS 90D Canon EOS 100D / Rebel SL1 / Kiss X7 Canon EOS 200D / Rebel SL2 / Kiss X9 Canon EOS 250D / Rebel SL3 / Kiss X10 Canon EOS 300D / Digital Rebel / Kiss Digital Canon EOS 350D / Digital Rebel XT / Kiss Digital N Canon EOS 400D / Digital Rebel XTi / Kiss Digital X Canon EOS 450D / Digital Rebel XSi / Kiss X2 Canon EOS 500D / Digital Rebel T1i / Kiss X3 Canon EOS 550D / Digital Rebel T2i / Kiss X4 Canon EOS 600D / Digital Rebel T3i / Kiss X5 Canon EOS 650D / Digital Rebel T4i / Kiss X6i Canon EOS 700D / Digital Rebel T5i / Kiss X7i Canon EOS 750D / Rebel T6i / Kiss X8i Canon EOS 760D / Rebel T6s / 8000D Canon EOS 800D / Rebel T7i / Kiss X9i Canon EOS 850D / Rebel T8i / Kiss X10i Canon EOS 1000D / Digital Rebel XS / Kiss F Canon EOS 1100D / Rebel T3 / Kiss X50 Canon EOS 1200D / Rebel T5 / Kiss X70 Canon EOS 1300D / Rebel T6 / Kiss X80 Canon EOS 1500D / 2000D / Rebel T7 / Kiss X90 Canon EOS 4000D / Rebel T100 / 3000D Canon cameras offered before 2003 The Astronomik EOS APS-C Clip-Filters fit into the original Canon EF to EF-M bayonet adapter and can be used with all variants of the Canon EOS M camera. Compatible lenses and adapters Model Compatibility Original Canon EF-S series lenses Lenses from third party manufacturers M42 lens adapters T2 lens adapters Technical Data Guaranteed transmission of more than 90% at the H-alpha line (656nm) Typical transmission of 93% at the H-alpha line Full-Width-Half Maximum (FWHM): 6nm Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters) Finely polished optical glass, free of any striae, residual stresses, and bubbles Extremely scratch-resistant and durable coating Completely resistant against high humidity and aging effects Astronomik MaxFR coating (Astronomik 6nm and 12nm Narrowband-Emissionline filters) Parfocal with other Astronomik filters Diffraction-limited Optimized spectral windows Delivered in a high-quality, long-lasting filter box Made in Germany Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Thanks to the high-precision machining of the glas substrate, all Astronomik filters are parfocal. The wedge errors are far below all common tolerances. Therefore, all issues concerning focal distances and the exact alignment of images from each color channel are effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR and MaxFR coatings are designed for optimal performance across a wide range of focal ratios of the optics used. Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios for best performance of that specific filter.
Astronomik H-alpha 12nm MaxFR Clip-Filter EOS XL
The Astronomik H-alpha filter is ideal for imaging HII regions from both light-polluted and dark observation sites. The Astronomik H-alpha filter significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background, allowing for long exposure times for deep and high-contrast images. The filter blocks the emission lines of high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, the maxima of typical LED lights, most lines of natural airglow, as well as most of the distracting moonlight. The Astronomik H-alpha filter effectively blocks all unwanted light from wavelengths other than 656nm, from ultraviolet (UV) to infrared (IR). The Astronomik H-alpha filter MUST NOT BE USED for solar observation! Difference between Astronomik 12nm, 6nm and 4nm filters The choice between 12nm, 6nm and 4nm Full-Width-Half-Maximum (FWHM) filters depends on your imaging conditions and camera type. There is no universal “best” option - each FWHM serves a specific purpose. The 12nm Astronomik Narrowband-Emissionline filters are optimized for use with system cameras with CMOS sensors. They are also a good choice for CCD cameras with normal or high dark current. The 12nm filters are also the preferred choice for cameras with an integrated or dual guiding sensor, as they show more guiding stars compared to filters with 6nm or 4nm FWHM. The 12nm filters are the most affordable way to get started with Narrowband-Emissionline filters. Usually, the background signal in images taken from suburban or dark-sky locations is limited by the sensor’s dark current rather than light pollution. Therefore, further suppression of the sky background by reducing the FWHM does not reveal more details of the object. The Astronomik MaxFR coating Both the Astronomik MFR and MaxFR coatings offer extremely high contrast, minimized stray light, no halos and needle-sharp stars. In addition, they provide the best possible blocking across the entire spectral range from UV to IR. The MaxFR coating ensures that the Astronomik Narrowband-Emissionline filters can be used with extremely fast optical systems such as the Celestron RASA and the Takahashi Epsilon Astrographs. Unlike other manufacturers' filters, which often require special “High-Speed” versions, Astronomik’s MaxFR filters maintain their transmission characteristics even with normal optical systems of slower focal ratios. Using a MaxFR filter with a normal optical system has no drawbacks and saves you a lot of money on multiple filter sets. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4. Clip-Filters for Canon EOS full-frame DSLR cameras Canon EOS full-frame DSLR cameras are an excellent choice for astrophotography. With Astronomik Clip-Filters, you can use our full range of filters with your camera to capture stunning images. Whether paired with a camera lens or a telescope, our Clip-Filters ensure maximum image quality and performance from your setup. The Astronomik Clip-Filters offer a number of practical advantages that make them an ideal choice for astrophotographers: Installing and removing the Astronomik Clip-Filter is very quick and easy and requires no extra tools or modifications to the camera body. They can be changed at any time, even at night. All lens functions, such as focus, aperture, and image stabilization remain fully functional. The Astronomik Clip-Filters are held securely in place without stressing the high-quality glass. The Astronomik Clip-Filters are designed and optimized for use with both standard camera lenses and telescopes. Through the Astronomik Clip-Filters, we were able to solve several common issues faced by astrophotographers: Large filters for large camera lenses are very expensive. Using a filter holder between the camera body and the lens prevents focusing to infinity. For very fast telescopes (low f-number) like the Vixen R200SS or the Takahashi “Epsilon” astrograph, a filter drawer or filter wheel can not be used because the distance to the corrector lenses would be changed. Long exposure times lead to dust settling on the camera’s sensor chip. Due to the very tight bayonet and the limited space inside the camera, the Astronomik EOS XL Clip-Filters cause a minimal obstruction in the corners. But this can be easily corrected by flatfielding. NOTE: Please store the Clip-Filter in the supplied storage box and do not leave it in the camera permanently. Use Astronomik filters for your Canon EOS full-frame DSLR camera and enjoy marvelous images with an ultra-light equipment! Compatible Canon EOS full-frame DSLR cameras Model Compatibility Canon EOS-1D (all variants) Canon EOS 5D no LiveView Canon EOS 5D Mark II Canon EOS 5D Mark III Canon EOS 5D Mark IV * Canon EOS 5DS * Canon EOS 5DS R * Canon EOS 6D Canon EOS 6D Mark II * * The camera’s electronics prevent the use of Clip-Filters. Technical Data Guaranteed transmission of more than 90% at the H-alpha line (656nm) Typical transmission of 96% at the H-alpha line Full-Width-Half Maximum (FWHM): 12nm Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters) Finely polished optical glass, free of any striae, residual stresses, and bubbles Extremely scratch-resistant and durable coating Completely resistant against high humidity and aging effects Astronomik MaxFR coating (Astronomik 6nm and 12nm Narrowband-Emissionline filters) Parfocal with other Astronomik filters Diffraction-limited Optimized spectral windows Delivered in a high-quality, long-lasting filter box Made in Germany Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Thanks to the high-precision machining of the glas substrate, all Astronomik filters are parfocal. The wedge errors are far below all common tolerances. Therefore, all issues concerning focal distances and the exact alignment of images from each color channel are effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR and MaxFR coatings are designed for optimal performance across a wide range of focal ratios of the optics used. Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios for best performance of that specific filter.
Astronomik H-alpha 6nm MaxFR 1,25" (M28,5)
The Astronomik H-alpha filter is ideal for imaging hydrogen nebulae from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background. The Astronomik H-alpha filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 656nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. The Astronomik H-alpha filter MUST NOT BE USED for solar observation!Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik H-alpha 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars. 12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at the H-alpha line (656nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at the H-alpha line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik OIII 12nm MaxFR Clip-Filter Sony alpha 7
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 12nm MaxFR 31mm
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 6nm MaxFR 31mm
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 12nm MaxFR Clip-Filter Nikon XL
The Astronomik H-alpha filter is ideal for imaging HII regions from both light-polluted and dark observation sites. The Astronomik H-alpha filter significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background, allowing for long exposure times for deep and high-contrast images. The filter blocks the emission lines of high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, the maxima of typical LED lights, most lines of natural airglow, as well as most of the distracting moonlight. The Astronomik H-alpha filter effectively blocks all unwanted light from wavelengths other than 656nm, from ultraviolet (UV) to infrared (IR). The Astronomik H-alpha filter MUST NOT BE USED for solar observation! Difference between Astronomik 12nm, 6nm and 4nm filters The choice between 12nm, 6nm and 4nm Full-Width-Half-Maximum (FWHM) filters depends on your imaging conditions and camera type. There is no universal “best” option - each FWHM serves a specific purpose. The 12nm Astronomik Narrowband-Emissionline filters are optimized for use with system cameras with CMOS sensors. They are also a good choice for CCD cameras with normal or high dark current. The 12nm filters are also the preferred choice for cameras with an integrated or dual guiding sensor, as they show more guiding stars compared to filters with 6nm or 4nm FWHM. The 12nm filters are the most affordable way to get started with Narrowband-Emissionline filters. Usually, the background signal in images taken from suburban or dark-sky locations is limited by the sensor’s dark current rather than light pollution. Therefore, further suppression of the sky background by reducing the FWHM does not reveal more details of the object. The Astronomik MaxFR coating Both the Astronomik MFR and MaxFR coatings offer extremely high contrast, minimized stray light, no halos and needle-sharp stars. In addition, they provide the best possible blocking across the entire spectral range from UV to IR. The MaxFR coating ensures that the Astronomik Narrowband-Emissionline filters can be used with extremely fast optical systems such as the Celestron RASA and the Takahashi Epsilon Astrographs. Unlike other manufacturers' filters, which often require special “High-Speed” versions, Astronomik’s MaxFR filters maintain their transmission characteristics even with normal optical systems of slower focal ratios. Using a MaxFR filter with a normal optical system has no drawbacks and saves you a lot of money on multiple filter sets. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4. Clip-Filter for Nikon full-frame DSLR cameras Nikon’s full-frame DSLR cameras are an excellent choice for astrophotography. With Astronomik Clip-Filters, you can use our full range of filters with your camera to capture stunning images. Whether paired with a camera lens or a telescope, our Clip-Filters ensure maximum image quality and performance from your setup. The Astronomik Clip-Filters offer a number of practical advantages that make them an ideal choice for astrophotographers: Installing and removing the Astronomik Clip-Filter is very quick and easy and requires no extra tools or modifications to the camera body. They can be changed at any time, even at night. All lens functions, such as focus, aperture, and image stabilization remain fully functional. The Astronomik Clip-Filters are held securely in place without stressing the high-quality glass. The Astronomik Clip-Filters are designed and optimized for use with both standard camera lenses and telescopes. Through the Astronomik Clip-Filters, we were able to solve several common issues faced by astrophotographers: Large filters for large camera lenses are very expensive. Using a filter holder between the camera body and the lens prevents focusing to infinity. For very fast telescopes (low f-number) like the Vixen R200SS or the Takahashi “Epsilon” astrograph, a filter drawer or filter wheel can not be used because the distance to the corrector lenses would be changed. Long exposure times lead to dust settling on the camera’s sensor chip. Due to the very tight bayonet and the limited space inside the camera, the Astronomik Nikon XL Clip-Filters cause a minimal obstruction in the corners. But this can be easily corrected by flatfielding. NOTE: Please store the Clip-Filter in the supplied storage box and do not leave it in the camera permanently. Use Astronomik filters for your Nikon full-frame DSLR camera and enjoy marvelous images with an ultra light equipment! Compatible Nikon full-frame DSLR cameras Model Compatibility Nikon D610 Nikon D750 Nikon D780 Limited * Nikon D800 Nikon D810 Nikon D850 Limited * * After a recent firmware update, Astronomik Nikon XL Clip-Filters can no longer be used with the Nikon D780 and D850 bodies. For these bodies, you can only use manual focus lenses or a T-adapter (with a telescope). Using lenses with electronic contacts will result in an error message, preventing the camera from functioning. Workaround: To use lenses with electronic contacts on the D780 and D850 with the Astronomik Nikon XL Clip-Filter installed, you can apply tape over the lens contacts. This will prevent the error message, allowing the camera to work normally. Technical Data Guaranteed transmission of more than 90% at the H-alpha line (656nm) Typical transmission of 96% at the H-alpha line Full-Width-Half Maximum (FWHM): 12nm Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters) Finely polished optical glass, free of any striae, residual stresses, and bubbles Extremely scratch-resistant and durable coating Completely resistant against high humidity and aging effects Astronomik MaxFR coating (Astronomik 6nm and 12nm Narrowband-Emissionline filters) Parfocal with other Astronomik filters Diffraction-limited Optimized spectral windows Delivered in a high-quality, long-lasting filter box Made in Germany Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Thanks to the high-precision machining of the glas substrate, all Astronomik filters are parfocal. The wedge errors are far below all common tolerances. Therefore, all issues concerning focal distances and the exact alignment of images from each color channel are effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR and MaxFR coatings are designed for optimal performance across a wide range of focal ratios of the optics used. Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios for best performance of that specific filter.
Astronomik H-alpha 12nm MaxFR 36mm
The Astronomik H-alpha filter is ideal for imaging hydrogen nebulae from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background. The Astronomik H-alpha filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 656nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. The Astronomik H-alpha filter MUST NOT BE USED for solar observation!Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik H-alpha 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars. 12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at the H-alpha line (656nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at the H-alpha line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik OIII 6nm MaxFR 31mm
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm and 4nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm and 4nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 6nm MaxFR Clip-Filter Nikon Z XL
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm and 6nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik OIII 12nm MaxFR 31mm
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm and 4nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm and 4nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik OIII 12nm MaxFR Clip-Filter Nikon Z XL
The Astronomik OIII filter is ideal for imaging nebulae showing oxygen emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 496nm and 501nm (OIII lines) and the sky background. The Astronomik OIII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 496nm and 501nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik OIII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm) and 88% (6nm) at the major OIII line (501nm)Typical transmission of 95% (12nm) and 92% (6nm) at the major OIII line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 6nm MaxFR 50mm
The Astronomik H-alpha filter is ideal for imaging hydrogen nebulae from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background. The Astronomik H-alpha filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 656nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. The Astronomik H-alpha filter MUST NOT BE USED for solar observation!Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik H-alpha 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars. 12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at the H-alpha line (656nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at the H-alpha line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 12nm MaxFR Clip-Filter EOS R XL
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm or 6nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 12nm and 6nm filtersThe 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way, as they typically halve the number of stars in the image. They are also suitable if you have a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are better suited for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they generally provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.Filters for even faster optics are available on request.Difference between Astronomik standard and XT Clip-FiltersThe new Astronomik XT-Filters are specifically designed for astrophotography with wide-angle lenses, delivering sharp and crisp star images all the way to the edges of the image. When using very short focal length lenses to take widefield images, standard Clip-Filters could introduce aberrations, stretching stars in the outermost corners of the image. To solve this issue, the new Astronomik XT-Filters are coated on an extremely thin substrate of only 0.3mm or 0,5mm thickness, significantly reducing these aberrations. Despite the reduced thickness, the Astronomik XT-Filters maintain the highest optical quality. They are manufactured using the same durable coating technology as all Astronomik filters. More information about our XT-Filters can be found here.Technical dataGuaranteed transmission of more than 90% (12nm and 6nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 12nm MaxFR 36mm
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 6nm MaxFR 2" (M48)
The Astronomik H-alpha filter is ideal for imaging hydrogen nebulae from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background. The Astronomik H-alpha filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 656nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. The Astronomik H-alpha filter MUST NOT BE USED for solar observation!Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik H-alpha 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars. 12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at the H-alpha line (656nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at the H-alpha line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik SII 6nm MaxFR 50mm
The Astronomik SII filter is ideal for imaging nebulae showing sulfur emissions from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 671.7nm and 673nm (SII lines) and the sky background. The Astronomik SII filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 671.7nm and 673nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik SII 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars.12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at both SII lines (671.7nm and 673.0nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at both SII lines Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.
Astronomik H-alpha 12nm MaxFR 31mm
The Astronomik H-alpha filter is ideal for imaging hydrogen nebulae from both light-polluted and dark observation sites. It significantly enhances the contrast between objects emitting light at 656nm (H-alpha line) and the sky background. The Astronomik H-alpha filter completely filters out the emission lines from high- and low-pressure sodium (Na)- and mercury (Hg)-vapor lamps, as well as all lines of natural airglow and most of the distracting moonlight.With a narrow bandwidth of either 12nm, 6nm or 4nm and high transmission rates, the filter effectively blocks all unwanted light from wavelengths other than 656nm from ultraviolet (UV) to infrared (IR).In areas with little light pollution, the background signal in images is usually limited by the sensor's dark current rather than light pollution. Therefore, further suppression of the sky background by reduction of the Full-Width-Half Maximum (FWHM) does not bring out more details in the object. The Astronomik H-alpha filter MUST NOT BE USED for solar observation!Imaging with Astronomik Narrowband-Emissionline filtersImaging with Astronomik Narrowband-Emissionline filters is the best way to capture great images from light-polluted sites as they effectively block all kinds of light pollution. An Astronomik H-alpha filter is usually the first step in this field of astrophotography, allowing you to take deep and contrasty images even under heavy light pollution or a full moon. Astronomik H-alpha filters are ideal for imaging all red-glowing nebulae. Astronomik OIII filters expand your imaging possibilities by capturing greenish and blueish structures, making planetary nebulae, star-forming regions and supernova remnants great targets. Completing your filter set with an Astronomik SII filter enables you to create false-color emission line images similar to those produced by the Hubble Space Telescope using the HSO (H-alpha, SII, OIII) palette. Difference between Astronomik H-alpha 4nm, 6nm and 12nm filters The 4nm and 6nm Astronomik Narrowband-Emissionline filters are ideal for imaging faint objects in star-crowded regions of the milky way. They are also recommended if you use a camera with very low dark current or if you are observing from a location with extreme light pollution.The 12nm Astronomik Narrowband-Emissionline filters are developed for use with typical DSLR cameras with CMOS sensors and CCD cameras with normal or high dark current. They are also the preferred choice for cameras with an integrated or dual guiding sensor, as they provide more guiding stars.Difference between Astronomik MFR and MaxFR coatingBoth the Astronomik MFR and MaxFR coatings give you the best possible blocking across the entire spectral range from UV to IR, extremely high contrast, minimized stray light, no halos and needle-sharp stars. 12nm MFR-coated filters can be used in all instruments with aperture ratios from f/3 to f/∞ without significant performance loss.6nm MFR-coated filters can be used in all instruments with aperture ratios from f/4 to f/∞ without significant performance loss.4nm MFR-coated filters can be used in all instruments with aperture ratios from f/4.5 to f/15 without significant performance loss.The MaxFR coating is designed to work perfectly with fast optical systems. For 12nm filters with MaxFR coating, this means unlimited usability from f/1.7 to f/6 and approximately 85% of the maximum transmission at a f/1.4.For 6nm filters with MaxFR coating, this means unlimited usability from f/2.2 to f/6 and approximately 90% of the maximum transmission at a f/2.4nm filters with MaxFR coating are currently in development.Filters for even faster optics are available on request.Technical dataGuaranteed transmission of more than 90% (12nm, 6nm and 4nm) at the H-alpha line (656nm)Typical transmission of 96% (12nm) and 93% (6nm and 4nm) at the H-alpha line Glass thickness: 1mm (except Astronomik OWB Type 3 and XT filters)Finely polished optical glass, free of any striae, residual stresses, and bubblesExtremely scratch-resistant and durable coatingCompletely resistant against high humidity and aging effectsAstronomik MFR coating (Astronomik Deep-Sky RGB, UV-IR Block L-1, L-2, L-3, and Narrowband-Emissionline filters)Parfocal with other Astronomik filtersDiffraction-limitedOptimized spectral windowsDelivered in a high-quality, long-lasting filter boxDue to the high-precision machining of the carrier substrate, all Astronomik filters are parfocal with wedge errors far below all common tolerances. Astronomik filters are diffraction-limited, ensuring that the optical performance (resolution and contrast) of your telescope is not compromised. Issues concerning focal distances and the exact alignment of images from each color channel are therefore effectively eliminated. All Astronomik filters are ideal for modern cameras, including both CMOS- and CCD-based models, ensuring you capture the best possible images with your equipment. Sharpness, contrast, and the absence of any reflections and halos are guaranteed. Even with bright stars in the field of view, nebulae and galaxies will be captured with the finest structures. The Astronomik MFR coating is designed for optimal performance across a wide range of focal ratios of the optics used.Every Astronomik filter undergoes a rigorous quality control process before delivery. Additionally, each Astronomik Narrowband-Emissionline filter is measured using a high-end PerkinElmer Spectrophotometer to ensure it meets the specifications published on our website. On the back of each Narrowband-Emissionline filter box, you will find a label detailing the precise spectral data for that specific filter, including the maximum transmission and the recommended range of focal ratios.